Contact
2K Duo
For the highest requirements
Water-based 2-component polyurethane finish for wooden floors. This very low-emissions coating is perfect in particular for event halls, offices or residential buildings.
Select variant
2K Duo
extra-matte
Properties
- Easy and safe application
- Qualified for various floorings
- Excellent wear resistance
- Certified anti-slip properties as per DIN EN 16165:2021-12 for work areas
- Meets all requirements of ÖNORM C2354:2009 for the highest stress class
Technical data sheets
Stress level
1
2
3
4
5
6
7
8
9
10
Residential
Commercial
Extreme
Further information
Range of use
Suitable for parquet and hardwood floors, as well as cork, linoleum or PVC floor coverings. Achieves the dynamic coefficient of friction as per DIN 18032 for sports flooring. Anti-slip as per DIN EN 16165:2021-12 evaluation group R9.
| Art.-no. |  |  |  |
|---|---|---|---|
11466-900004-22-000 | 5 kg | 2 | 96 |
- Shake the mixture, add the hardener in a ratio of 5:1 and mix in by shaking. If partial quantities are to be mixed, use the LOBA mixing container or weigh the quantities out. Can be used for 2 hours after mixing.
- The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
- The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
- In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
- To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
- Transfer material to a LOBA varnish bucket before applying.
- Shake the contents well.
- Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
Thinner / Mixing
The product is ready for use and must not be reduced!Application tool / application rate
LOBA roller Deluxe 120 and LOBA roller Microfaser 100-120 / 100-120 ml(g)/m² = 8-10 m²/l(kg)Drying time
- Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
- The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
- Drying times are valid for +20°C and 50% relative humidity.
Intermediate sanding
Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will improve the optical appearence of the surface.Use LOBASAND perforated pad P120 or finer, alternatively Sanding Net P120 or finer.Carefully remove dust before overcoating.Use on parquet and hardwood floors:
- Prepare and prime the substrate properly.
- Allow the primer to dry as specified.
- Apply by roller.
- Dry.
- Intermediate sanding.
- Apply second coating layer by roller.
Use on cork:
Seal only after the adhesive has set adequately.Untreated natural cork:- Apply three layers of coating by roller.
- Allow the first layer to dry overnight (reduces the risk of granule swelling).
- Intermediate sanding before the final application.
Prefinished corkObserve the cork supplier's instructions. If suitable for recoating, apply one or two layers of coating after an intermediate sanding
Renovation / recoating of old coatingsBasic cleaning with CareRemover. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralise). After drying, carry out a thorough intermediate sanding. Apply coating in one or two layers by rollerColoring tipTo achieve a brightening/whitening effect on light-coloured substrates, we recommend adding LOBA Whitener according to the technical information of the product. In order to minimize color reactions with tannins, the first layer of the paint must be applied to untreated cork in the delivery form without color additive. Subsequent drying overnight is necessary.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.
- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Renovation / recoating of old coatingsBasic cleaning with CareRemover. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralise). After drying, carry out a thorough intermediate sanding. Apply coating in one or two layers by rollerColoring tipTo achieve a brightening/whitening effect on light-coloured substrates, we recommend adding LOBA Whitener according to the technical information of the product. In order to minimize color reactions with tannins, the first layer of the paint must be applied to untreated cork in the delivery form without color additive. Subsequent drying overnight is necessary.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.
- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.
Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Consumption calculator
Area
m²
Consumption
= ?
Application device
Layers
References
Gripsholms Världshus
Suitable Loba products
PerforatedPad & DustPad
EasyPrime
EasyFill
Roller Microfibre 100-120
Whitener
Roller Deluxe 120
2K Intensive
- Transparent
ParkettCare
- satin
Coating bucket, bucket liner
Amberizer
Roller frame, roller extension
Suitable Wakol products
D 1640 Parquet Adhesive
D 1690 Parquet Adhesive
MS 228 Ready-to-lay Parquet Adhesive, elastic
MS 230 Parquet Adhesive, elastic
MS 232 Parquet Adhesive, elastic
MS 260 Parquet Adhesive, firm-elastic
MS 261
MS 262 Parquet Adhesive, firm-elastic
MS 265
MS 269
MS 290 Parquet Adhesive, shear-resistant
MS 292 Parquet Adhesive, shear-resistant
PU 210 Parquet Adhesive
PU 215 Parquet Adhesive
PU 216 Parquet Adhesive
PU 220 Parquet Adhesive
PU 225 Parquet Adhesive
PU 385 Parquet Adhesive, shear-resistant
2K Duo
satin
Properties
- Easy and safe application
- Particularly low emission according to EMICODE EC1 Plus
- Qualified for various floorings
- Excellent wear resistance
- Excellent chemical resistance
- Certified anti-slip properties as per DIN EN 16165:2021-12 for work areas
- Satisfies wear class C as per Ö-Norm Standard C 2354 (very heavy traffic).
Further information
Range of use
Suitable for parquet and hardwood floors, as well as cork, linoleum or PVC floor coverings. Achieves the dynamic coefficient of friction as per DIN 18032 for sports flooring. Anti-slip as per DIN EN 16165:2021-12 evaluation group R9.
| Art.-no. | | | |
|---|---|---|---|
11466-900003-15-000 | 1 kg | 6 | 360 |
11466-900003-22-000 | 5 kg | 2 | 96 |
- Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBA Mixing Container or a scale to weigh out the components. Usable up to 2 hours after mixing.
- The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
- The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
- In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
- To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
- Transfer material to a LOBA varnish bucket before applying.
- Shake the contents well.
- Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
Thinner / Mixing
The product is ready for use and must not be reduced!Application tool / application rate
LOBA roller Deluxe 120 and LOBA roller Microfaser 100-120 / 100-120 ml(g)/m² = 8-10 m²/l(kg)Drying time
- Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
- The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
- Drying times are valid for +20°C and 50% relative humidity.
Intermediate sanding
Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will improve the optical appearence of the surface.Use LOBASAND perforated pad P120 or finer, alternatively Sanding Net P120 or finer.Carefully remove dust before overcoating.Use on parquet and hardwood floors:
- Prepare and prime the substrate properly.
- Allow the primer to dry as specified.
- Apply by roller.
- Dry.
- Intermediate sanding.
- Apply second coating layer by roller.
Use on cork:
Seal only after the adhesive has set adequately.Untreated natural cork:- Apply three layers of coating by roller.
- Allow the first layer to dry overnight (reduces the risk of granule swelling).
- Intermediate sanding before the final application.
Prefinished corkObserve the cork supplier's instructions. If suitable for recoating, apply one or two layers of coating after an intermediate sanding
Renovation / recoating of old coatingsBasic cleaning with CareRemover. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralise). After drying, carry out a thorough intermediate sanding. Apply coating in one or two layers by rollerColoring tipTo achieve a brightening/whitening effect on light-coloured substrates, we recommend adding LOBA Whitener according to the technical information of the product. In order to minimize color reactions with tannins, the first layer of the paint must be applied to untreated cork in the delivery form without color additive. Subsequent drying overnight is necessary.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.
- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Renovation / recoating of old coatingsBasic cleaning with CareRemover. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralise). After drying, carry out a thorough intermediate sanding. Apply coating in one or two layers by rollerColoring tipTo achieve a brightening/whitening effect on light-coloured substrates, we recommend adding LOBA Whitener according to the technical information of the product. In order to minimize color reactions with tannins, the first layer of the paint must be applied to untreated cork in the delivery form without color additive. Subsequent drying overnight is necessary.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.
- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.
Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Consumption calculator
Area
m²
Consumption
= ?
Application device
Layers
References
Dorp Hotel
Evenement ruimte
Evenement ruimte 2
Hotel Altes Gut
Residence Sandringham
Starbucks Camps Bay
The Address Restaurant
Suitable Loba products
EasyFill
PerforatedPad & DustPad
EasyPrime
Roller Deluxe 120
2K Intensive
- Transparent
Roller Microfibre 100-120
Refresh
Whitener
Small roller for edges
Cleaner
Suitable Wakol products
D 1640 Parquet Adhesive
D 1690 Parquet Adhesive
MS 228 Ready-to-lay Parquet Adhesive, elastic
MS 230 Parquet Adhesive, elastic
MS 232 Parquet Adhesive, elastic
MS 260 Parquet Adhesive, firm-elastic
MS 261
MS 262 Parquet Adhesive, firm-elastic
MS 265
MS 269
MS 290 Parquet Adhesive, shear-resistant
MS 292 Parquet Adhesive, shear-resistant
PU 210 Parquet Adhesive
PU 215 Parquet Adhesive
PU 216 Parquet Adhesive
PU 220 Parquet Adhesive
PU 225 Parquet Adhesive
PU 385 Parquet Adhesive, shear-resistant
2K Duo
semi-gloss
Properties
- Easy and safe application
- Particularly low emission according to EMICODE EC1 Plus
- Qualified for various floorings
- Excellent wear resistance
- Excellent chemical resistance
- Certified anti-slip properties as per DIN EN 16165:2021-12 for work areas
- Satisfies wear class C as per Ö-Norm Standard C 2354 (very heavy traffic).
Technical data sheets
Stress level
1
2
3
4
5
6
7
8
9
10
Residential
Commercial
Extreme
Further information
Range of use
Suitable for parquet and hardwood floors, as well as cork, linoleum or PVC floor coverings. Achieves the dynamic coefficient of friction as per DIN 18032 for sports flooring. Anti-slip as per DIN EN 16165:2021-12 evaluation group R9.
| Art.-no. | | | |
|---|---|---|---|
11466-900001-15-000 | 1 kg | 6 | 360 |
11466-900001-22-000 | 5 kg | 2 | 96 |
- Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBA Mixing Container or a scale to weigh out the components. Usable up to 2 hours after mixing.
- The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
- The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
- In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
- To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
- Transfer material to a LOBA varnish bucket before applying.
- Shake the contents well.
- Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
Thinner / Mixing
The product is ready for use and must not be reduced!Application tool / application rate
LOBA roller Deluxe 120 and LOBA roller Microfaser 100-120 / 100-120 ml(g)/m² = 8-10 m²/l(kg)Drying time
- Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
- The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
- Drying times are valid for +20°C and 50% relative humidity.
Intermediate sanding
Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will improve the optical appearence of the surface.Use LOBASAND perforated pad P120 or finer, alternatively Sanding Net P120 or finer.Carefully remove dust before overcoating.Use on parquet and hardwood floors:
- Prepare and prime the substrate properly.
- Allow the primer to dry as specified.
- Apply by roller.
- Dry.
- Intermediate sanding.
- Apply second coating layer by roller.
Use on cork:
Seal only after the adhesive has set adequately.Untreated natural cork:- Apply three layers of coating by roller.
- Allow the first layer to dry overnight (reduces the risk of granule swelling).
- Intermediate sanding before the final application.
Prefinished corkObserve the cork supplier's instructions. If suitable for recoating, apply one or two layers of coating after an intermediate sanding
Renovation / recoating of old coatingsBasic cleaning with CareRemover. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralise). After drying, carry out a thorough intermediate sanding. Apply coating in one or two layers by rollerColoring tipTo achieve a brightening/whitening effect on light-coloured substrates, we recommend adding LOBA Whitener according to the technical information of the product. In order to minimize color reactions with tannins, the first layer of the paint must be applied to untreated cork in the delivery form without color additive. Subsequent drying overnight is necessary.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.
- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Renovation / recoating of old coatingsBasic cleaning with CareRemover. Use a rotary disk buffing machine and a LOBASAND SpecialPad green. Care product residues must be completely removed. Even small amounts of residue can adversely effect the bond of the coating. Clean with clear water (neutralise). After drying, carry out a thorough intermediate sanding. Apply coating in one or two layers by rollerColoring tipTo achieve a brightening/whitening effect on light-coloured substrates, we recommend adding LOBA Whitener according to the technical information of the product. In order to minimize color reactions with tannins, the first layer of the paint must be applied to untreated cork in the delivery form without color additive. Subsequent drying overnight is necessary.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.
- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
To achieve a color intensification on natural cork and brownish and reddish colored cork floors, we recommend adding LOBA Amberizer according to the technical information of the product.
Linoleum and PVC:
Thoroughly clean using LOBA CareRemover according to the technical information. A single-disc machine with a green LOBASAND special pad must be used. Residues from care products must be completely removed, as even small traces of residue can prevent the finish from adhering properly. Wipe (neutralise) with clear water. Allow to dry. Factory finished coverings must be matted with a LOBASAND Polishing fleece after thorough cleaning (1 polishing fleece is sufficient for approx. 20 m2). Roll on a layer of finish.Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Consumption calculator
Area
m²
Consumption
= ?
Application device
Layers
References
Agio Oros
Crown Plaza
Spa Facility
Suitable Loba products
EasyPrime
PerforatedPad & DustPad
EasyFill
Roller Microfibre 100-120
Whitener
2K Intensive
- Transparent
Roller Deluxe 120
ProColor
- Various colors
Cleaner
Coating bucket, bucket liner
Amberizer
Suitable Wakol products
D 1640 Parquet Adhesive
D 1690 Parquet Adhesive
MS 228 Ready-to-lay Parquet Adhesive, elastic
MS 230 Parquet Adhesive, elastic
MS 232 Parquet Adhesive, elastic
MS 260 Parquet Adhesive, firm-elastic
MS 261
MS 262 Parquet Adhesive, firm-elastic
MS 265
MS 269
MS 290 Parquet Adhesive, shear-resistant
MS 292 Parquet Adhesive, shear-resistant
PU 210 Parquet Adhesive
PU 215 Parquet Adhesive
PU 216 Parquet Adhesive
PU 220 Parquet Adhesive
PU 225 Parquet Adhesive
PU 385 Parquet Adhesive, shear-resistant
2K Duo
gloss
Properties
- Easy and safe application
- Qualified for various floorings
- Excellent wear resistance
- High-gloss surface
- Meets all requirements of ÖNORM C2354:2009 for the highest stress class
Further information
Range of use
Suitable for parquet and wooden floors. Achieves the dynamic coefficient of friction as per DIN 18032 for sports flooring.
| Art.-no. | | | |
|---|---|---|---|
11466-900002-22-000 | 5 kg | 2 | 96 |
- Shake product, add hardener to base at a ratio of 10 : 1 and then shake to mix. For mixing smaller quantities, use the LOBA Mixing Container or a scale to weigh out the components. Usable up to 2 hours after mixing.
- The surface must be professionally sanded. The floor must be dry and free of any old coatings, oil, grease, wax, silicone, sanding dust and other impurities.
- The optimal processing conditions are room temperature +15°C to + 25°C, floor temperature +15°C to +22°C, rel. humidity 40% to 75%, material temperature +18°C to + 25°C, max. wood moisture 12%, sufficiently ventilate working rooms.
- In order to prevent parquet damage, the room temperature should be set to the annual average expected for the use of the product.
- To reduce the risk of excessive swelling, we recommend applying a maximum of 2 roll applications per day.
- Transfer material to a LOBA varnish bucket before applying.
- Shake the contents well.
- Observe general and, if necessary, product-specific occupational health and safety regulations. Further information can be found in the GISCODE-related operating instructions which are available under www.wingis-online.de.
- This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol parquet adhesives may be found in the "Connected Systems" Matrix: www.loba.de/connected-systems
Thinner / Mixing
The product is ready for use and must not be reduced!Application tool / application rate
LOBA roller Deluxe 120 and LOBA roller Microfaser 100-120 / 100-120 ml(g)/m² = 8-10 m²/l(kg)Drying time
- Can be carefully walked on, intermediate sanding can be performed and can be varnished over after no less than 4 hours.
- Light use after 24 hours.
- Full use and covering possible after 5 days.
- The floor can be covered earlier by using LOBA Cover 400, for details see the TI for the product.
- Drying times are valid for +20°C and 50% relative humidity.
Intermediate sanding
Able to recoat without intermediate sanding within the first 24 hours. After this time, an intermediate sanding is necessary. An intermediate sanding before the last application will improve the optical appearence of the surface.Use LOBASAND perforated pad P180 or finer, alternatively Sanding Net P180 or finer.Carefully remove dust before overcoating.Use on parquet and hardwood floors:
- Prepare and prime the substrate properly.
- Allow the primer to dry as specified.
- Apply by roller.
- Dry.
- Intermediate sanding.
- Apply second coating layer by roller.
Suitable product combinations
We recommend using a primer:
To minimise side bonding and to seal off wood constituents, e.g. in exotic timber.- EasyPrime
- VivaPrime
- 2K Intensive
- PrimaSeal Plus (contains solvent)
AdditivesThe range of application, properties and appearance can be extended by combining with LOBA additives. Please refer to the respective technical information of the additives for possible combinations, detailed application information, and drying times.
Consumption calculator
Area
m²
Consumption
= ?
Application device
Layers
Suitable Loba products
EasyPrime
EasyFill
PerforatedPad & DustPad
Roller Deluxe 120
Roller Microfibre 100-120
Coating bucket, bucket liner
2K Intensive
- Transparent
Whitener
CareRemover
UV-Protect
Amberizer
Suitable Wakol products
D 1640 Parquet Adhesive
D 1690 Parquet Adhesive
MS 228 Ready-to-lay Parquet Adhesive, elastic
MS 230 Parquet Adhesive, elastic
MS 232 Parquet Adhesive, elastic
MS 260 Parquet Adhesive, firm-elastic
MS 261
MS 262 Parquet Adhesive, firm-elastic
MS 265
MS 269
MS 290 Parquet Adhesive, shear-resistant
MS 292 Parquet Adhesive, shear-resistant
PU 210 Parquet Adhesive
PU 215 Parquet Adhesive
PU 216 Parquet Adhesive
PU 220 Parquet Adhesive
PU 225 Parquet Adhesive